Not draining, not cleaning, leaking, not starting, error codes. Bosch, Miele, KitchenAid, Samsung, LG, Whirlpool — we know them all.
Spray arms calcify, heating elements scale up, and door latches wear out faster here than in soft-water cities. Drain pumps clog on food debris, control boards die after 8–10 years, and the door switch — the most common fault by far — is a 30-minute swap once you know it’s the cause.
We carry door latches, drain pumps, spray arms, and descaling kits for Bosch, Miele, KitchenAid, Whirlpool, and Samsung on the van — the brands that cover most of our weekly calls. If the wash pump or motor has failed on a high-end European unit, that’s the one fault where replacement sometimes makes more sense than repair, and we’ll tell you straight.
Drain pump, garbage-disposal air gap, a clogged drain hose, or the check valve. If you’ve got standing water at the end of every cycle, this is where we look first.
Extremely common with Toronto hard water — spray arms clog with mineral buildup and stop spraying above them. Also: failing wash pump, detergent dispenser not releasing, or a rinse-aid issue. We de-scale and test on-site.
Door seal, tub split, float switch stuck open, or a loose clamp. Where the water pools on the floor tells us where to start.
Door latch (by far the most common — the switch inside the latch wears out), control board, or a tripped thermal fuse. Power at the outlet is the first check.
Bosch E01–E24, Whirlpool F-codes, Samsung flashing LEDs — each brand tells a different story. We decode against the service manual and diagnose the root cause, not just the reported code.
Heating element, rinse-aid dispenser, or the vent fan on heated-dry cycles. Some models (condensation dryers) just need more rinse aid and stacking adjustments.
Wax motor failure — specific to KitchenAid and Whirlpool. The soap stays sealed and the cycle runs without detergent. Straightforward part swap.
Drain trap biofilm or a check valve letting sink water back into the tub. We clean the trap, re-seat the check valve, and add a monthly maintenance recommendation.
Water inlet valve or a stuck float. The valve screen clogs with sediment in Toronto — a 5-minute fix.
Thermistor or control board. The heater isn’t reaching target temp, so the cycle doesn’t advance.
We price every repair case-by-case after we see the unit in person. Here’s exactly how it works.
Tell us the symptom, the make and model, and when you’re free. We’ll lock in a same-day or next-day window.
A licensed tech inspects the appliance in your home, pinpoints the actual fault, and confirms the parts needed. No guesswork over the phone.
You get an exact, all-in repair price before any work begins. If the fix isn’t worth it on an older unit, we’ll tell you straight.
Approve the quote and the $89 diagnostic comes off your final bill. Decide to pass and you only pay the $89 — no obligation either way.
Every appliance, brand, and fault is different. That’s why we quote case-by-case after seeing the unit, not before.
Bosch, Miele, KitchenAid, Whirlpool, Samsung, LG, GE, Frigidaire, Maytag, Fisher & Paykel, and more. Integrated panel-ready and standalone — both routine for us.
Toronto water hardness. Add rinse aid to the dispenser and consider switching to a detergent that includes a water softener. If it persists after those changes, your spray arms are probably clogged — we clean them during a service visit.
Bosch parts cost more up front but Bosch dishwashers also have longer service intervals — fewer visits over the life of the unit. KitchenAid parts are cheaper but failures cluster earlier. Net lifetime cost is similar.
Yes — regular call. We detach the integrated panel carefully, service, re-align. No visible marks.
Depends on brand and symptom. A pump replacement on a 12-year-old Bosch — usually yes. A control board on a 10-year-old budget unit — usually not worth it. We’ll tell you straight after diagnosing on-site, with the actual repair number in hand.
Tell us the symptom. We’ll call within two hours.
